lora sx1262
1.0.0
Apache Nuttx RTO의 SX1262의 경우 lorawan 지점을 참조하십시오.
기사를 읽으십시오 ...
"Pinedio Lora SX1262 USB 어댑터 용 Linux 드라이버 구축"
"Pinedio Stack BL604 RISC-V 보드의 Lorawan"
"Pinecone BL602는 Lorawan의 대화"
"Pinedio Stack BL604 RISC-V 보드의 네트워크"
주의 : 29 바이트 이상의 Pinedio USB (BL602 아님)에서 lora 메시지를 보내면 메시지 손상이 발생합니다!
주의 : 28 바이트 이상의 Pinedio USB (BL602 아님)에 LORA 메시지를 받으면 메시지 손상이 발생합니다!
(CH341 SPI는 32 바이트 블록을 전송하는 데 어려움이있는 것 같습니다)
BL602 / BL604의 경우 :이 드라이버를 기존 BL602 / BL604 프로젝트에 추가하려면 :
cd bl_iot_sdk/components/3rdparty
git submodule add https://github.com/lupyuen/lora-sx1262SX1262 드라이버의 Semtech의 참조 구현에서 포팅되었습니다 ...
https://github.com/lora-net/loramac--node/tree/master/src/radio/sx126x
Pinebook Pro Manjaro Arm64에 Pinedio USB 드라이버를 구축하려면 ...
# # Install DKMS
sudo pacman -Syu dkms base-devel --needed
# # Install Kernel Headers for Manjaro: https://linuxconfig.org/manjaro-linux-kernel-headers-installation
uname -r
# # Should show "5.14.12-1-MANJARO-ARM" or similar
sudo pacman -S linux-headers
pacman -Q | grep headers
# # Should show "linux-headers 5.14.12-1" or similar
# # Reboot to be safe
sudo reboot now
# # Install CH341 SPI Driver
git clone https://github.com/rogerjames99/spi-ch341-usb.git
pushd spi-ch341-usb
# # TODO: Edit Makefile and change...
# # KERNEL_DIR = /usr/src/linux-headers-$(KVERSION)/
# # To...
# # KERNEL_DIR = /lib/modules/$(KVERSION)/build
make
sudo make install
popd
# # Unload the module ch341 if it has been automatically loaded
lsmod | grep ch341
sudo rmmod ch341
# # Load the new module
sudo modprobe spi-ch341-usb
# # Plug in PineDio USB and check that the module has been correctly loaded.
# # See dmesg Log below. This needs to be checked every time we reboot
# # our computer and when we plug in PineDio USB.
dmesg
# # If we see "spi_ch341_usb: loading out-of-tree module taints kernel",
# # Unplug PineDio USB, run "sudo rmmod ch341", plug in PineDio USB again
# # and recheck dmesg.
# # Download PineDio USB Driver
git clone --recursive https://github.com/lupyuen/lora-sx1262
cd lora-sx1262
# # TODO: Edit src/main.c and uncomment READ_REGISTERS, SEND_MESSAGE or RECEIVE_MESSAGE.
# # See "PineDio USB Operations" below
# # Build PineDio USB Driver
make
# # Run PineDio USB Driver Demo.
# # See Output Log below.
sudo ./lora-sx1262Pinedio USB 및 CH341 SPI에 대한 자세한 내용 :
https://wiki.pine64.org/wiki/jf%27S_NOTE_ON_PINEDIO_DEVICES#RAW_COMMUNICICATION_BETWEN_USB_LORA_ADAPTER_AND_PINEDIO_STACK
Pinedio USB 데모는 3 개의 작업을 지원합니다 ...
SX1262 레지스터 읽기 :
src/main.c 및 무례한 편집 ...
#define READ_REGISTERS(아래의 레지스터 로그 참조)
LORA 메시지 보내기 :
src/main.c 및 무례한 편집 ...
#define SEND_MESSAGE(아래 메시지 보내기 로그 참조)
LORA 메시지 받기 :
src/main.c 및 무례한 편집 ...
#define RECEIVE_MESSAGE(아래의 메시지 받기 로그 참조)
CH341 GPIO 프로그래밍은 불완전합니다. 우리는 ...
GPIO 핀을 시작하십시오 : SX126xIoInit
src/sx126x-linux.c#l65-l77
DIO1에 대한 GPIO 인터럽트 핸들러 등록 : SX126xIoIrqInit
src/sx126x-linux.c#l79-l91
GPIO를 통해 SX1262를 재설정하십시오 : SX126xReset
(지금은 Pinedio USB를 수동으로 뽑아 SX1262를 재설정합니다)
src/sx126x-linux.c#l149-l169
GPIO를 통해 SX1262 바쁜 상태를 확인하십시오 : SX126xWaitOnBusy
(지금 우리는 10 밀리 초)
src/sx126x-linux.c#l171-l182
DIO1 핀 상태를 가져옵니다 : SX126xGetDio1PinState
src/sx126x-linux.c#l337-l344
또한 백그라운드에서 LORA 메시지를 받으려면 배경 스레드가 필요합니다 ...
SRC/MAIN.C#L355-L408
Pinedio USB 및 CH341 GPIO에 대한 자세한 내용 :
https://wiki.pine64.org/wiki/jf%27S_NOTE_ON_PINEDIO_DEVICES#RAW_COMMUNICICATION_BETWEN_USB_LORA_ADAPTER_AND_PINEDIO_STACK
Pinedio USB 데모의 출력 로그 ...
Pinedio USB에서 SX1262 레지스터를 읽으십시오.
read_registers
SX126xIoInit
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: a2 22
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 00 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x00 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 01 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x01 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 02 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x02 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 03 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x03 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 04 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x04 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 05 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x05 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 06 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x06 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 07 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x07 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 08 00 00
spi rx: a2 a2 a2 a2 80
TODO: SX126xWaitOnBusy
Register 0x08 = 0x80
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 09 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x09 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0a 00 00
spi rx: a2 a2 a2 a2 01
TODO: SX126xWaitOnBusy
Register 0x0a = 0x01
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0b 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0b = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0c 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0c = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0d 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0d = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0e 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0e = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0f 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0f = 0x00
Done!
DMESG 읽기 레지스터 로그는 아래를 참조하십시오.
Pinedio USB에서 29 바이트 로라 메시지를 전송합니다.
주의 : 29 바이트 이상의 Pinedio USB (BL602 아님)에서 lora 메시지를 보내면 메시지 손상이 발생합니다!
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: ac 2c
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: ac ac
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 02 01 02 01 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSend: PreambleLength=8, HeaderType=0, PayloadLength=29, CrcMode=1, InvertIQ=0
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 1d 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=2, data_length=29
spi tx: 0e 00 50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 83 00 00 00
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
Done!
Pinedio USB가 전송 한 29 바이트 LORA 메시지는 ...
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
DMESG 보내기 메시지 로그는 아래를 참조하십시오.
우리 가이 로라 송신기를 Rakwireless Wisblock에서 실행할 때 ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
Wisblock에 의해 전송 된 28 바이트 메시지는 Pinedio USB에 의해 확인됩니다.
주의 : 28 바이트 이상의 Pinedio USB (BL602 아님)에 LORA 메시지를 받으면 메시지 손상이 발생합니다!
Pinedio USB 수신 메시지 로그는 다음과 같습니다.
(Wisblock 송신기 로그는 아래를 참조하십시오)
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: d4 54
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 2f 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1c 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
Done!
Pinedio USB가받은 28 바이트 LORA 메시지는 ...
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
DMESG 수신 메시지 로그는 아래를 참조하십시오.
우리가 Rakwireless Wisblock 에서이 Lora 수신기를 실행할 때 ...
https://github.com/lupyuen/wisblock-lora-receiver
Pinedio USB가 전송 한 29 바이트 메시지는 Wisblock에 의해 확인됩니다 ...
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRaP2P Rx Test
=====================================
Starting Radio.Rx
OnRxDone: Timestamp=18, RssiValue=-28 dBm, SnrValue=13, Data=50 49 4E 47 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18
주의 : 29 바이트 이상의 Pinedio USB (BL602 아님)에서 lora 메시지를 보내면 메시지 손상이 발생합니다!
Pinedio Stack BL604에서 sdk_app_lora 펌웨어를 실행하면 Wisblock은 64 바이트 메시지를받습니다.
그러나 Pinedio USB가 보낸 64 바이트 메시지는 Wisblock이받을 때 지속적으로 차지합니다.
(CH341 SPI는 32 바이트 블록을 전송하는 데 어려움이있는 것 같습니다)
우리 가이 로라 송신기를 Rakwireless Wisblock에서 실행할 때 ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
Wisblock에 의해 전송 된 28 바이트 메시지는 Pinedio USB에 의해 확인됩니다.
Wisblock 송신기 로그는 다음과 같습니다.
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRap2p Tx Test
=====================================
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
주의 : 28 바이트 이상의 Pinedio USB (BL602 아님)에 LORA 메시지를 받으면 메시지 손상이 발생합니다!
(CH341 SPI는 32 바이트 블록을 전송하는 데 어려움이있는 것 같습니다)
Pinedio USB를 Pinebook Pro에 연결할 때 DMESG 로그 ...
usb 3-1:
new full-speed USB device number 2 using xhci-hcd
New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
New USB device strings: Mfr=0, Product=2, SerialNumber=0
Product: USB UART-LPT
spi-ch341-usb 3-1:1.0:
ch341_usb_probe:
connect device
bNumEndpoints=3
endpoint=0 type=2 dir=1 addr=2
endpoint=1 type=2 dir=0 addr=2
endpoint=2 type=3 dir=1 addr=1
ch341_cfg_probe:
output cs0 SPI slave with cs=0
output cs0 gpio=0 irq=0
output cs1 SPI slave with cs=1
output cs1 gpio=1 irq=1
output cs2 SPI slave with cs=2
output cs2 gpio=2 irq=2
input gpio4 gpio=3 irq=3
input gpio6 gpio=4 irq=4
input err gpio=5 irq=5
input pemp gpio=6 irq=6
input int gpio=7 irq=7 (hwirq)
input slct gpio=8 irq=8
input wait gpio=9 irq=9
input autofd gpio=10 irq=10
input addr gpio=11 irq=11
output ini gpio=12 irq=12
output write gpio=13 irq=13
output scl gpio=14 irq=14
output sda gpio=15 irq=15
ch341_spi_probe:
start
SPI master connected to SPI bus 1
SPI device /dev/spidev1.0 created
SPI device /dev/spidev1.1 created
SPI device /dev/spidev1.2 created
done
ch341_irq_probe:
start
irq_base=94
done
ch341_gpio_probe:
start
ch341_gpio_get_direction:
gpio=cs0 dir=0
gpio=cs1 dir=0
gpio=cs2 dir=0
gpio=gpio4 dir=1
gpio=gpio6 dir=1
gpio=err dir=1
gpio=pemp dir=1
gpio=int dir=1
gpio=slct dir=1
gpio=wait dir=1
gpio=autofd dir=1
gpio=addr dir=1
gpio=ini dir=0
gpio=write dir=0
gpio=scl dir=0
gpio=sda dir=0
ch341_gpio_probe:
registered GPIOs from 496 to 511
done
connected
ch341_gpio_poll_function:
start
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
이는 최신 CH341 SPI 드라이버가로드되었음을 의미합니다.
대신 이것을 본다면 ...
usb 3-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 3-1: Product: USB UART-LPT
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
ch341 3-1:1.0: ch341-uart converter detected
usb 3-1: ch341-uart converter now attached to ttyUSB0
spi_ch341_usb: loading out-of-tree module taints kernel.
usbcore: registered new interface driver spi-ch341-usb
이는 구형 CH341 비 SPI 드라이버가로드되었음을 의미합니다.
이것을 고치려면 ...
플러그 Pinedio USB
입력하다...
sudo rmmod ch341Pinedio USB를 연결하십시오
입력하다...
dmesg메시지를 다시 확인하십시오.
DMESG 로그 Pinedio USB를 읽을 때 SX1262 레지스터 ...
audit: type=1105 audit(1635493969.129:144): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
audit: type=1106 audit(1635493969.499:145): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
DMESG 로그 Pinedio USB가 29 바이트 로라 패킷을 전송할 때 ...
주의 : 29 바이트 이상의 Pinedio USB (BL602 아님)에서 lora 메시지를 보내면 메시지 손상이 발생합니다!
audit: type=1105 audit(1634994194.295:1270): pid=72110 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
audit: type=1701 audit(1634994203.075:1271): auid=1000 uid=0 gid=0 ses=4 subj==unconfined pid=72111 comm="lora-sx1262" exe="/home/luppy/lora-sx1262/lora-sx1262" sig=6 res=1
64 바이트 패킷을 전송하려고하면 DMESG 로그에 표시되지 않습니다.
DMESG 로그 Pinedio USB가 28 바이트 로라 패킷을받을 때 ...
주의 : 28 바이트 이상의 Pinedio USB (BL602 아님)에 LORA 메시지를 받으면 메시지 손상이 발생합니다!
audit: type=1105 audit(1635046697.907:371): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
audit: type=1106 audit(1635046711.037:372): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
핀은 여기에서 include/sx126x-board.h 로 정의됩니다
include/sx126x-board.h :
// Below are the pin numbers for PineDio Stack BL604 with onboard SX1262.
// TODO: Change the pin numbers for your SX1262 connection to BL602 / BL604
#define SX126X_SPI_IDX 0 // SPI Port 0
#define SX126X_SPI_SDI_PIN 0 // SPI Serial Data In Pin (formerly MISO)
#define SX126X_SPI_SDO_PIN 17 // SPI Serial Data Out Pin (formerly MOSI)
#define SX126X_SPI_CLK_PIN 11 // SPI Clock Pin
#define SX126X_SPI_CS_PIN 15 // SPI Chip Select Pin
#define SX126X_SPI_CS_OLD 8 // Unused SPI Chip Select Pin
#define SX126X_NRESET 18 // Reset Pin
#define SX126X_DIO1 19 // DIO1
#define SX126X_BUSY_PIN 10 // Busy Pin
#define SX126X_DEBUG_CS_PIN 5 // Debug Chip Select Pin, mirrors the High / Low State of SX1262 Chip Select Pin. Set to -1 if not needed.
#define SX126X_TCXO_WAKEUP_TIME 5 // Time required for the TCXO to wakeup (milliseconds)
#define SX126X_SPI_BAUDRATE (200 * 1000) // SPI Frequency (200 kHz) 드라이버와 함께 LORA 패킷을 전송하고 받으려면 sdk_app_lora BL602 데모 펌웨어를 실행하십시오.
sdk_app_lora : LORA SX1262 / SX1276 용 블602 데모 펌웨어다음은 샘플 로그입니다 ...
# create_task
# init_driver
SX126xReset
SX126xIoInit
SX126X interrupt init
SX126X register handler: GPIO 11
SX126xWakeup
SX126xGetDeviceId: SX1262
SX126xSetRfTxPower
SX126xGetDeviceId: SX1262
# send_message
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
RadioOnRxTimeoutIrq
Rx timeout
