lora sx1262
1.0.0
Pour SX1262 sur Apache Nuttx RTOS, voir la branche lorawan
Lisez les articles ...
"Construisez un pilote Linux pour l'adaptateur USB Pinedio Lora SX1262"
"Lorawan sur Pinedio Stack BL604 RISC-V Board"
"Pinecone BL602 parle Lorawan"
"Le réseau de choses sur Pinedio Stack BL604 RISC-V Board"
ATTENTION: L'envoi d'un message LORA sur Pinedio USB (pas BL602) au-dessus de 29 octets provoquera la corruption du message!
ATTENTION: Recevoir un message LORA sur Pinedio USB (pas BL602) au-dessus de 28 octets provoquera la corruption du message!
(CH341 SPI semble avoir du mal à transférer un bloc de 32 octets)
Pour BL602 / BL604: Pour ajouter ce pilote à un projet BL602 / BL604 existant:
cd bl_iot_sdk/components/3rdparty
git submodule add https://github.com/lupyuen/lora-sx1262Portée à partir de la mise en œuvre de référence de SemTech du pilote SX1262 ...
https://github.com/lora-net/loramac-node/tree/master/src/radio/sx126x
Pour construire Pinedio USB Driver sur Pinebook Pro Manjaro Arm64 ...
# # Install DKMS
sudo pacman -Syu dkms base-devel --needed
# # Install Kernel Headers for Manjaro: https://linuxconfig.org/manjaro-linux-kernel-headers-installation
uname -r
# # Should show "5.14.12-1-MANJARO-ARM" or similar
sudo pacman -S linux-headers
pacman -Q | grep headers
# # Should show "linux-headers 5.14.12-1" or similar
# # Reboot to be safe
sudo reboot now
# # Install CH341 SPI Driver
git clone https://github.com/rogerjames99/spi-ch341-usb.git
pushd spi-ch341-usb
# # TODO: Edit Makefile and change...
# # KERNEL_DIR = /usr/src/linux-headers-$(KVERSION)/
# # To...
# # KERNEL_DIR = /lib/modules/$(KVERSION)/build
make
sudo make install
popd
# # Unload the module ch341 if it has been automatically loaded
lsmod | grep ch341
sudo rmmod ch341
# # Load the new module
sudo modprobe spi-ch341-usb
# # Plug in PineDio USB and check that the module has been correctly loaded.
# # See dmesg Log below. This needs to be checked every time we reboot
# # our computer and when we plug in PineDio USB.
dmesg
# # If we see "spi_ch341_usb: loading out-of-tree module taints kernel",
# # Unplug PineDio USB, run "sudo rmmod ch341", plug in PineDio USB again
# # and recheck dmesg.
# # Download PineDio USB Driver
git clone --recursive https://github.com/lupyuen/lora-sx1262
cd lora-sx1262
# # TODO: Edit src/main.c and uncomment READ_REGISTERS, SEND_MESSAGE or RECEIVE_MESSAGE.
# # See "PineDio USB Operations" below
# # Build PineDio USB Driver
make
# # Run PineDio USB Driver Demo.
# # See Output Log below.
sudo ./lora-sx1262En savoir plus sur Pinedio USB et CH341 SPI:
https://wiki.pine64.org/wiki/JF%27S_NOTE_ON_PINEdio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack
La démo Pinedio USB prend en charge 3 opérations ...
Lire les registres SX1262:
Modifier src/main.c et non-comment ...
#define READ_REGISTERS(Voir le journal du registre de lecture ci-dessous)
Envoyer le message LORA:
Modifier src/main.c et non-comment ...
#define SEND_MESSAGE(Voir le journal des messages Envoyer ci-dessous)
Recevoir le message LORA:
Modifier src/main.c et non-comment ...
#define RECEIVE_MESSAGE(Voir le journal des messages de réception ci-dessous)
Notez que la programmation CH341 GPIO est incomplète. Nous devons...
Init les broches GPIO: SX126xIoInit
src / sx126x-linux.c # l65-l77
Enregistrez le gestionnaire d'interruptions GPIO pour Dio1: SX126xIoIrqInit
SRC / SX126X-LINUX.C # L79-L91
Réinitialiser SX1262 via GPIO: SX126xReset
(Pour l'instant, nous réinitialisons SX1262 en débranchant manuellement Pinedio USB)
SRC / SX126X-LINUX.C # L149-L169
Vérifiez SX1262 State Busy via GPIO: SX126xWaitOnBusy
(Pour l'instant nous dormons 10 millisecondes)
src / sx126x-linux.c # l171-l182
Obtenez l'état de la broche Dio1: SX126xGetDio1PinState
src / sx126x-linux.c # l337-l344
Nous avons également besoin de threads d'arrière-plan pour recevoir des messages LORA en arrière-plan ...
src / main.c # l355-l408
En savoir plus sur Pinedio USB et CH341 GPIO:
https://wiki.pine64.org/wiki/JF%27S_NOTE_ON_PINEdio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack
Journal de sortie de la démo USB Pinedio ...
Lire les registres SX1262 sur Pinedio USB:
read_registers
SX126xIoInit
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: a2 22
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 00 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x00 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 01 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x01 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 02 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x02 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 03 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x03 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 04 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x04 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 05 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x05 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 06 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x06 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 07 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x07 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 08 00 00
spi rx: a2 a2 a2 a2 80
TODO: SX126xWaitOnBusy
Register 0x08 = 0x80
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 09 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x09 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0a 00 00
spi rx: a2 a2 a2 a2 01
TODO: SX126xWaitOnBusy
Register 0x0a = 0x01
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0b 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0b = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0c 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0c = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0d 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0d = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0e 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0e = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0f 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0f = 0x00
Done!
Voir ci-dessous pour le journal des registres de lecture DMESG.
Transmettre le message Lora de 29 octets sur Pinedio USB:
ATTENTION: L'envoi d'un message LORA sur Pinedio USB (pas BL602) au-dessus de 29 octets provoquera la corruption du message!
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: ac 2c
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: ac ac
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 02 01 02 01 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSend: PreambleLength=8, HeaderType=0, PayloadLength=29, CrcMode=1, InvertIQ=0
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 1d 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=2, data_length=29
spi tx: 0e 00 50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 83 00 00 00
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
Done!
Notez que le message Lora de 29 octets transmis par Pinedio USB est ...
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
Voir ci-dessous pour le journal des messages d'envoi DMESG.
Lorsque nous dirigeons cet émetteur Lora sur Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
Le message de 28 octets transmis par Wisblock est reçu OK par Pinedio USB.
ATTENTION: Recevoir un message LORA sur Pinedio USB (pas BL602) au-dessus de 28 octets provoquera la corruption du message!
Voici le journal des messages de réception de Pinedio USB ...
(Voir ci-dessous pour le journal de l'émetteur Wisblock)
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: d4 54
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 2f 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1c 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
Done!
Notez que le message Lora de 28 octets reçu par Pinedio USB est ...
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
Voir ci-dessous pour le journal des messages de réception DMESG.
Lorsque nous dirigeons ce récepteur Lora sur Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-receiver
Le message de 29 octets transmis par Pinedio USB est reçu OK par Wisblock ...
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRaP2P Rx Test
=====================================
Starting Radio.Rx
OnRxDone: Timestamp=18, RssiValue=-28 dBm, SnrValue=13, Data=50 49 4E 47 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18
ATTENTION: L'envoi d'un message LORA sur Pinedio USB (pas BL602) au-dessus de 29 octets provoquera la corruption du message!
Lorsque nous exécutons le firmware sdk_app_lora sur Pinedio Stack BL604, Wisblock reçoit le message de 64 octets OK.
Mais les messages de 64 octets envoyés par Pinedio USB sont toujours brouillés lorsqu'ils sont reçus par Wisblock.
(CH341 SPI semble avoir du mal à transférer un bloc de 32 octets)
Lorsque nous dirigeons cet émetteur Lora sur Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
Le message de 28 octets transmis par Wisblock est reçu OK par Pinedio USB.
Voici le journal de l'émetteur Wisblock ...
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRap2p Tx Test
=====================================
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
ATTENTION: Recevoir un message LORA sur Pinedio USB (pas BL602) au-dessus de 28 octets provoquera la corruption du message!
(CH341 SPI semble avoir du mal à transférer un bloc de 32 octets)
Journal DMESG lors du branchement Pinedio USB à Pinebook Pro ...
usb 3-1:
new full-speed USB device number 2 using xhci-hcd
New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
New USB device strings: Mfr=0, Product=2, SerialNumber=0
Product: USB UART-LPT
spi-ch341-usb 3-1:1.0:
ch341_usb_probe:
connect device
bNumEndpoints=3
endpoint=0 type=2 dir=1 addr=2
endpoint=1 type=2 dir=0 addr=2
endpoint=2 type=3 dir=1 addr=1
ch341_cfg_probe:
output cs0 SPI slave with cs=0
output cs0 gpio=0 irq=0
output cs1 SPI slave with cs=1
output cs1 gpio=1 irq=1
output cs2 SPI slave with cs=2
output cs2 gpio=2 irq=2
input gpio4 gpio=3 irq=3
input gpio6 gpio=4 irq=4
input err gpio=5 irq=5
input pemp gpio=6 irq=6
input int gpio=7 irq=7 (hwirq)
input slct gpio=8 irq=8
input wait gpio=9 irq=9
input autofd gpio=10 irq=10
input addr gpio=11 irq=11
output ini gpio=12 irq=12
output write gpio=13 irq=13
output scl gpio=14 irq=14
output sda gpio=15 irq=15
ch341_spi_probe:
start
SPI master connected to SPI bus 1
SPI device /dev/spidev1.0 created
SPI device /dev/spidev1.1 created
SPI device /dev/spidev1.2 created
done
ch341_irq_probe:
start
irq_base=94
done
ch341_gpio_probe:
start
ch341_gpio_get_direction:
gpio=cs0 dir=0
gpio=cs1 dir=0
gpio=cs2 dir=0
gpio=gpio4 dir=1
gpio=gpio6 dir=1
gpio=err dir=1
gpio=pemp dir=1
gpio=int dir=1
gpio=slct dir=1
gpio=wait dir=1
gpio=autofd dir=1
gpio=addr dir=1
gpio=ini dir=0
gpio=write dir=0
gpio=scl dir=0
gpio=sda dir=0
ch341_gpio_probe:
registered GPIOs from 496 to 511
done
connected
ch341_gpio_poll_function:
start
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
Cela signifie que le nouveau pilote CH341 SPI a été chargé.
Si nous voyons cela à la place ...
usb 3-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 3-1: Product: USB UART-LPT
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
ch341 3-1:1.0: ch341-uart converter detected
usb 3-1: ch341-uart converter now attached to ttyUSB0
spi_ch341_usb: loading out-of-tree module taints kernel.
usbcore: registered new interface driver spi-ch341-usb
Cela signifie que l'ancien pilote non SPI CH341 a été chargé.
Pour réparer cela ...
Débrancher Pinedio USB
Entrer...
sudo rmmod ch341Branchez Pinedio USB
Entrer...
dmesgEt revérifiez les messages.
Journal DMESG Lorsque Pinedio USB lit les registres SX1262 ...
audit: type=1105 audit(1635493969.129:144): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
audit: type=1106 audit(1635493969.499:145): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
Journal DMESG Lorsque Pinedio USB transmet un paquet Lora de 29 octets ...
ATTENTION: L'envoi d'un message LORA sur Pinedio USB (pas BL602) au-dessus de 29 octets provoquera la corruption du message!
audit: type=1105 audit(1634994194.295:1270): pid=72110 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
audit: type=1701 audit(1634994203.075:1271): auid=1000 uid=0 gid=0 ses=4 subj==unconfined pid=72111 comm="lora-sx1262" exe="/home/luppy/lora-sx1262/lora-sx1262" sig=6 res=1
Notez que si nous essayons de transmettre un paquet de 64 octets, il n'apparaît pas dans le journal DMESG.
Journal DMESG Lorsque Pinedio USB reçoit un paquet Lora de 28 octets ...
ATTENTION: Recevoir un message LORA sur Pinedio USB (pas BL602) au-dessus de 28 octets provoquera la corruption du message!
audit: type=1105 audit(1635046697.907:371): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
audit: type=1106 audit(1635046711.037:372): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
Les broches sont définies ici dans include/sx126x-board.h
De include/sx126x-board.h :
// Below are the pin numbers for PineDio Stack BL604 with onboard SX1262.
// TODO: Change the pin numbers for your SX1262 connection to BL602 / BL604
#define SX126X_SPI_IDX 0 // SPI Port 0
#define SX126X_SPI_SDI_PIN 0 // SPI Serial Data In Pin (formerly MISO)
#define SX126X_SPI_SDO_PIN 17 // SPI Serial Data Out Pin (formerly MOSI)
#define SX126X_SPI_CLK_PIN 11 // SPI Clock Pin
#define SX126X_SPI_CS_PIN 15 // SPI Chip Select Pin
#define SX126X_SPI_CS_OLD 8 // Unused SPI Chip Select Pin
#define SX126X_NRESET 18 // Reset Pin
#define SX126X_DIO1 19 // DIO1
#define SX126X_BUSY_PIN 10 // Busy Pin
#define SX126X_DEBUG_CS_PIN 5 // Debug Chip Select Pin, mirrors the High / Low State of SX1262 Chip Select Pin. Set to -1 if not needed.
#define SX126X_TCXO_WAKEUP_TIME 5 // Time required for the TCXO to wakeup (milliseconds)
#define SX126X_SPI_BAUDRATE (200 * 1000) // SPI Frequency (200 kHz) Pour transmettre et recevoir des paquets LORA avec le pilote, exécutez le firmware de démonstration sdk_app_lora BL602 ...
sdk_app_lora : BL602 Firmware de démonstration pour LORA SX1262 / SX1276Voici un exemple de journal ...
# create_task
# init_driver
SX126xReset
SX126xIoInit
SX126X interrupt init
SX126X register handler: GPIO 11
SX126xWakeup
SX126xGetDeviceId: SX1262
SX126xSetRfTxPower
SX126xGetDeviceId: SX1262
# send_message
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
RadioOnRxTimeoutIrq
Rx timeout
