Beranda>Terkait pemrograman>Kode Sumber AI
Unduh

Driver Lora untuk Semtech SX1262 di Linux (adaptor Pinedio USB) dan BL602 (Pinedio Stack BL604)

Untuk SX1262 di Apache Nuttx Rtos, lihat Cabang lorawan

Baca artikelnya ...

  • "Bangun driver Linux untuk adaptor USB Pinedio Lora SX1262"

  • "Lorawan di Pinedio Stack BL604 RISC-V Board"

  • "Pinecone Bl602 berbicara Lorawan"

  • "The Things Network di Pinedio Stack BL604 RISC-V Board"

PERHATIAN: Mengirim pesan LORA di Pinedio USB (bukan BL602) di atas 29 byte akan menyebabkan korupsi pesan!

PERHATIAN: Menerima pesan LORA di Pinedio USB (bukan BL602) di atas 28 byte akan menyebabkan korupsi pesan!

(CH341 SPI tampaknya mengalami kesulitan mentransfer blok 32 byte)

Untuk BL602 / BL604: Untuk menambahkan driver ini ke proyek BL602 / BL604 yang ada: 

 cd bl_iot_sdk/components/3rdparty
git submodule add https://github.com/lupyuen/lora-sx1262

Porting dari implementasi referensi Semtech dari driver SX1262 ...

https://github.com/lora-net/loramac-node/tree/master/src/radio/sx126x

Bangun Pinedio USB Driver

Untuk membangun driver USB Pinedio di PineBook Pro Manjaro Arm64 ... 

 # # Install DKMS
sudo pacman -Syu dkms base-devel --needed

# # Install Kernel Headers for Manjaro: https://linuxconfig.org/manjaro-linux-kernel-headers-installation
uname -r 
# # Should show "5.14.12-1-MANJARO-ARM" or similar
sudo pacman -S linux-headers
pacman -Q | grep headers
# # Should show "linux-headers 5.14.12-1" or similar

# # Reboot to be safe
sudo reboot now

# # Install CH341 SPI Driver
git clone https://github.com/rogerjames99/spi-ch341-usb.git
pushd spi-ch341-usb
# # TODO: Edit Makefile and change...
# #   KERNEL_DIR  = /usr/src/linux-headers-$(KVERSION)/
# # To...
# #   KERNEL_DIR  = /lib/modules/$(KVERSION)/build
make
sudo make install
popd

# # Unload the module ch341 if it has been automatically loaded
lsmod | grep ch341
sudo rmmod ch341

# # Load the new module
sudo modprobe spi-ch341-usb

# # Plug in PineDio USB and check that the module has been correctly loaded.
# # See dmesg Log below. This needs to be checked every time we reboot
# # our computer and when we plug in PineDio USB.
dmesg

# # If we see "spi_ch341_usb: loading out-of-tree module taints kernel",
# # Unplug PineDio USB, run "sudo rmmod ch341", plug in PineDio USB again
# # and recheck dmesg.

# # Download PineDio USB Driver
git clone --recursive https://github.com/lupyuen/lora-sx1262
cd lora-sx1262

# # TODO: Edit src/main.c and uncomment READ_REGISTERS, SEND_MESSAGE or RECEIVE_MESSAGE.
# # See "PineDio USB Operations" below

# # Build PineDio USB Driver
make

# # Run PineDio USB Driver Demo.
# # See Output Log below.
sudo ./lora-sx1262

Lebih lanjut tentang Pinedio USB dan CH341 SPI:

https://wiki.pine64.org/wiki/jf%27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_Adapter_and_pinedio_stack

Operasi USB Pinedio

Demo USB Pinedio mendukung 3 operasi ...

  1. Baca register SX1262:

    Edit src/main.c dan uncomment ... 

     #define READ_REGISTERS

    (Lihat log register baca di bawah)

  2. Kirim pesan lora:

    Edit src/main.c dan uncomment ... 

     #define SEND_MESSAGE

    (Lihat Log Pesan Kirim di bawah)

  3. Terima pesan Lora:

    Edit src/main.c dan uncomment ... 

     #define RECEIVE_MESSAGE

    (Lihat log pesan terima di bawah)

Perhatikan bahwa pemrograman GPIO CH341 tidak lengkap. Kita perlu ...

  1. Init pin GPIO: SX126xIoInit

    src/sx126x-linux.c#l65-l77

  2. Register GPIO Interrupt Handler untuk DIO1: SX126xIoIrqInit

    src/sx126x-linux.c#l79-l91

  3. Reset SX1262 via GPIO: SX126xReset

    (Untuk saat ini kami mengatur ulang SX1262 dengan secara manual mencabut Pinedio USB)

    src/sx126x-linux.c#l149-l169

  4. Periksa status sibuk SX1262 melalui GPIO: SX126xWaitOnBusy

    (Untuk saat ini kami tidur 10 milidetik)

    src/sx126x-linux.c#l171-l182

  5. Dapatkan status PIN DIO1: SX126xGetDio1PinState

    src/sx126x-linux.c#l337-l344

Kami juga membutuhkan utas latar belakang untuk menerima pesan Lora di latar belakang ...

src/main.c#l355-l408

Lebih lanjut tentang Pinedio USB dan CH341 GPIO:

https://wiki.pine64.org/wiki/jf%27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_Adapter_and_pinedio_stack

Pinedio USB Output Log

Log keluaran dari demo Pinedio USB ...

Baca register

Baca register SX1262 di Pinedio USB: 

 read_registers
SX126xIoInit
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: a2 22 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 00 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x00 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 01 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x01 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 02 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x02 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 03 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x03 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 04 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x04 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 05 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x05 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 06 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x06 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 07 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x07 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 08 00 00 
spi rx: a2 a2 a2 a2 80 
TODO: SX126xWaitOnBusy
Register 0x08 = 0x80
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 09 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x09 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0a 00 00 
spi rx: a2 a2 a2 a2 01 
TODO: SX126xWaitOnBusy
Register 0x0a = 0x01
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0b 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0b = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0c 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0c = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0d 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0d = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0e 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0e = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0f 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0f = 0x00
Done!

Lihat di bawah untuk log register baca DMESG.

Kirim pesan

Pesan Lora 29-Byte di Pinedio USB:

PERHATIAN: Mengirim pesan LORA di Pinedio USB (bukan BL602) di atas 29 byte akan menyebabkan korupsi pesan! 

 gcc -o lora-sx1262 
npl/linux/src/os_eventq.cc 
 
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o 
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble  
-pthread -lrt -lstdc++  

cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: ac 2c 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: ac ac 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a 
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00 
spi rx: a2 a2 a2 a2 04 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00 
spi rx: a2 a2 a2 a2 0d 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 02 01 02 01 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSend: PreambleLength=8, HeaderType=0, PayloadLength=29, CrcMode=1, InvertIQ=0
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 1d 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=2, data_length=29
spi tx: 0e 00 50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 83 00 00 00 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
Done!

Perhatikan bahwa pesan Lora 29-byte yang dikirimkan oleh Pinedio USB adalah ... 

 send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18

Lihat di bawah untuk DMESG Kirim Log Pesan.

Menerima pesan

Saat kami menjalankan pemancar Lora ini di Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio

Pesan 28-byte yang dikirimkan oleh Wisblock diterima OK oleh Pinedio USB.

PERHATIAN: Menerima pesan LORA di Pinedio USB (bukan BL602) di atas 28 byte akan menyebabkan korupsi pesan!

Inilah log Pesan Pinedio USB menerima ...

(Lihat di bawah untuk log pemancar Wisblock) 

 gcc -o lora-sx1262 
npl/linux/src/os_eventq.cc 
 
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o 
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble  
-pthread -lrt -lstdc++  

cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: d4 54 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b 
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00 
spi rx: a2 a2 a2 a2 04 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00 
spi rx: a2 a2 a2 a2 0d 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1e 30 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1e 2f 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1c 30 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
Done!

Perhatikan bahwa pesan Lora 28-byte yang diterima oleh Pinedio USB adalah ... 

 Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID

Lihat di bawah untuk log pesan menerima DMESG.

Log Penerima Wisblock

Saat kami menjalankan penerima Lora ini di Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-receiver

Pesan 29-byte yang dikirimkan oleh Pinedio USB diterima OK oleh Wisblock ... 

 > Executing task: platformio device monitor <

--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201  9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRaP2P Rx Test
=====================================
Starting Radio.Rx
OnRxDone: Timestamp=18, RssiValue=-28 dBm, SnrValue=13, Data=50 49 4E 47 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18

PERHATIAN: Mengirim pesan LORA di Pinedio USB (bukan BL602) di atas 29 byte akan menyebabkan korupsi pesan!

Saat kami menjalankan firmware sdk_app_lora di Pinedio Stack BL604, Wisblock menerima pesan 64-byte OK.

Tetapi pesan 64-byte yang dikirim oleh Pinedio USB secara konsisten kacau ketika diterima oleh Wisblock.

(CH341 SPI tampaknya mengalami kesulitan mentransfer blok 32 byte)

Log pemancar Wisblock

Saat kami menjalankan pemancar Lora ini di Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio

Pesan 28-byte yang dikirimkan oleh Wisblock diterima OK oleh Pinedio USB.

Inilah log pemancar Wisblock ... 

 > Executing task: platformio device monitor <

--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201  9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRap2p Tx Test
=====================================
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone

PERHATIAN: Menerima pesan LORA di Pinedio USB (bukan BL602) di atas 28 byte akan menyebabkan korupsi pesan!

(CH341 SPI tampaknya mengalami kesulitan mentransfer blok 32 byte)

Pinedio USB DMESG LOG

Hubungkan USB

DMESG LOG Saat mencolokkan Pinedio USB ke PineBook Pro ... 

 usb 3-1:
new full-speed USB device number 2 using xhci-hcd
New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
New USB device strings: Mfr=0, Product=2, SerialNumber=0
Product: USB UART-LPT

spi-ch341-usb 3-1:1.0:
  ch341_usb_probe:
    connect device
    bNumEndpoints=3
      endpoint=0 type=2 dir=1 addr=2
      endpoint=1 type=2 dir=0 addr=2
      endpoint=2 type=3 dir=1 addr=1

  ch341_cfg_probe:
    output cs0 SPI slave with cs=0
    output cs0    gpio=0  irq=0 
    output cs1 SPI slave with cs=1
    output cs1    gpio=1  irq=1 
    output cs2 SPI slave with cs=2
    output cs2    gpio=2  irq=2 
    input  gpio4  gpio=3  irq=3 
    input  gpio6  gpio=4  irq=4 
    input  err    gpio=5  irq=5 
    input  pemp   gpio=6  irq=6 
    input  int    gpio=7  irq=7 (hwirq)
    input  slct   gpio=8  irq=8 
    input  wait   gpio=9  irq=9 
    input  autofd gpio=10 irq=10 
    input  addr   gpio=11 irq=11 
    output ini    gpio=12 irq=12 
    output write  gpio=13 irq=13 
    output scl    gpio=14 irq=14 
    output sda    gpio=15 irq=15 

  ch341_spi_probe:
    start
    SPI master connected to SPI bus 1
    SPI device /dev/spidev1.0 created
    SPI device /dev/spidev1.1 created
    SPI device /dev/spidev1.2 created
    done

  ch341_irq_probe:
    start
    irq_base=94
    done

  ch341_gpio_probe: 
    start

  ch341_gpio_get_direction:
    gpio=cs0    dir=0
    gpio=cs1    dir=0
    gpio=cs2    dir=0
    gpio=gpio4  dir=1
    gpio=gpio6  dir=1
    gpio=err    dir=1
    gpio=pemp   dir=1
    gpio=int    dir=1
    gpio=slct   dir=1
    gpio=wait   dir=1
    gpio=autofd dir=1
    gpio=addr   dir=1
    gpio=ini    dir=0
    gpio=write  dir=0
    gpio=scl    dir=0
    gpio=sda    dir=0

  ch341_gpio_probe:
    registered GPIOs from 496 to 511
    done
    connected

  ch341_gpio_poll_function:
    start

usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart

Ini berarti bahwa driver SPI CH341 yang lebih baru telah dimuat.

Hubungkan USB gagal

Jika kita melihat ini sebagai gantinya ... 

 usb 3-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 3-1: Product: USB UART-LPT
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
ch341 3-1:1.0: ch341-uart converter detected
usb 3-1: ch341-uart converter now attached to ttyUSB0
spi_ch341_usb: loading out-of-tree module taints kernel.
usbcore: registered new interface driver spi-ch341-usb

Ini berarti driver non-SPI CH341 yang lebih tua telah dimuat.

Untuk memperbaiki ini ...

  1. Cabut USB Pinedio

  2. Memasuki... 

    sudo rmmod ch341

  3. Plug in pinedio usb

  4. Memasuki... 

    dmesg

    Dan periksa ulang pesannya.

Baca register

DMESG LOG Saat Pinedio USB sedang membaca SX1262 Register ... 

 audit: type=1105 audit(1635493969.129:144): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
audit: type=1106 audit(1635493969.499:145): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'

Kirim pesan

DMESG LOG Saat Pinedio USB sedang mentransmisikan paket Lora 29-byte ...

PERHATIAN: Mengirim pesan LORA di Pinedio USB (bukan BL602) di atas 29 byte akan menyebabkan korupsi pesan! 

 audit: type=1105 audit(1634994194.295:1270): pid=72110 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
audit: type=1701 audit(1634994203.075:1271): auid=1000 uid=0 gid=0 ses=4 subj==unconfined pid=72111 comm="lora-sx1262" exe="/home/luppy/lora-sx1262/lora-sx1262" sig=6 res=1

Perhatikan bahwa jika kami mencoba mengirimkan paket 64-byte, itu tidak akan muncul di log DMESG.

Menerima pesan

DMESG LOG Saat Pinedio USB menerima paket Lora 28-byte ...

PERHATIAN: Menerima pesan LORA di Pinedio USB (bukan BL602) di atas 28 byte akan menyebabkan korupsi pesan! 

 audit: type=1105 audit(1635046697.907:371): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
audit: type=1106 audit(1635046711.037:372): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'

Hubungkan BL602 ke SX1262

Pin didefinisikan di sini dalam include/sx126x-board.h

Dari include/sx126x-board.h : 

 //  Below are the pin numbers for PineDio Stack BL604 with onboard SX1262.
//  TODO: Change the pin numbers for your SX1262 connection to BL602 / BL604
#define SX126X_SPI_IDX           0  //  SPI Port 0
#define SX126X_SPI_SDI_PIN       0  //  SPI Serial Data In Pin  (formerly MISO)
#define SX126X_SPI_SDO_PIN      17  //  SPI Serial Data Out Pin (formerly MOSI)
#define SX126X_SPI_CLK_PIN      11  //  SPI Clock Pin
#define SX126X_SPI_CS_PIN       15  //  SPI Chip Select Pin
#define SX126X_SPI_CS_OLD        8  //  Unused SPI Chip Select Pin
#define SX126X_NRESET           18  //  Reset Pin
#define SX126X_DIO1             19  //  DIO1
#define SX126X_BUSY_PIN         10  //  Busy Pin
#define SX126X_DEBUG_CS_PIN      5  //  Debug Chip Select Pin, mirrors the High / Low State of SX1262 Chip Select Pin. Set to -1 if not needed.
#define SX126X_TCXO_WAKEUP_TIME  5  //  Time required for the TCXO to wakeup (milliseconds)
#define SX126X_SPI_BAUDRATE  (200 * 1000)  //  SPI Frequency (200 kHz)

Firmware demo BL602

Untuk mengirimkan dan menerima paket Lora dengan driver, jalankan firmware demo sdk_app_lora BL602 ...

  • sdk_app_lora : firmware demo bl602 untuk lora sx1262 / sx1276

Ini contoh log ... 

 # create_task

# init_driver
SX126xReset
SX126xIoInit
SX126X interrupt init
SX126X register handler: GPIO 11
SX126xWakeup
SX126xGetDeviceId: SX1262
SX126xSetRfTxPower
SX126xGetDeviceId: SX1262

# send_message

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# send_message
SX126xWakeup

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# send_message
SX126xWakeup

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup
RadioOnRxTimeoutIrq
Rx timeout
Memperluas
Informasi Tambahan
Aplikasi Terkait
Direkomendasikan untuk Anda
Informasi Terkait Semua