lora sx1262
1.0.0
Para SX1262 en Apache Nuttx RTOs, ver la rama de lorawan
Lea los artículos ...
"Construya un controlador Linux para el adaptador USB Pinedio Lora SX1262"
"Lorawan en Pinedio Stack BL604 Risc-V Junta"
"Pinecone BL602 habla Lorawan"
"The Things Network en Pinedio Stack BL604 Risc-V Board"
Precaución: Enviar un mensaje Lora en Pinedio USB (no BL602) por encima de 29 bytes causará corrupción de mensajes.
PRECAUCIÓN: ¡Recibir un mensaje Lora en Pinedio USB (no BL602) por encima de 28 bytes causará corrupción de mensajes!
(CH341 SPI parece tener problemas para transferir un bloque de 32 bytes)
Para BL602 / BL604: para agregar este controlador a un proyecto BL602 / BL604 existente:
cd bl_iot_sdk/components/3rdparty
git submodule add https://github.com/lupyuen/lora-sx1262Portado desde la implementación de referencia de Semtech del controlador SX1262 ...
https://github.com/lora-net/loramac-node/tree/master/src/radio/sx126x
Para construir Pinedio USB Driver en Pinebook Pro Manjaro Arm64 ...
# # Install DKMS
sudo pacman -Syu dkms base-devel --needed
# # Install Kernel Headers for Manjaro: https://linuxconfig.org/manjaro-linux-kernel-headers-installation
uname -r
# # Should show "5.14.12-1-MANJARO-ARM" or similar
sudo pacman -S linux-headers
pacman -Q | grep headers
# # Should show "linux-headers 5.14.12-1" or similar
# # Reboot to be safe
sudo reboot now
# # Install CH341 SPI Driver
git clone https://github.com/rogerjames99/spi-ch341-usb.git
pushd spi-ch341-usb
# # TODO: Edit Makefile and change...
# # KERNEL_DIR = /usr/src/linux-headers-$(KVERSION)/
# # To...
# # KERNEL_DIR = /lib/modules/$(KVERSION)/build
make
sudo make install
popd
# # Unload the module ch341 if it has been automatically loaded
lsmod | grep ch341
sudo rmmod ch341
# # Load the new module
sudo modprobe spi-ch341-usb
# # Plug in PineDio USB and check that the module has been correctly loaded.
# # See dmesg Log below. This needs to be checked every time we reboot
# # our computer and when we plug in PineDio USB.
dmesg
# # If we see "spi_ch341_usb: loading out-of-tree module taints kernel",
# # Unplug PineDio USB, run "sudo rmmod ch341", plug in PineDio USB again
# # and recheck dmesg.
# # Download PineDio USB Driver
git clone --recursive https://github.com/lupyuen/lora-sx1262
cd lora-sx1262
# # TODO: Edit src/main.c and uncomment READ_REGISTERS, SEND_MESSAGE or RECEIVE_MESSAGE.
# # See "PineDio USB Operations" below
# # Build PineDio USB Driver
make
# # Run PineDio USB Driver Demo.
# # See Output Log below.
sudo ./lora-sx1262Más sobre Pinedio USB y CH341 SPI:
https://wiki.pine64.org/wiki/jf%27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack
La demostración de Pinedio USB admite 3 operaciones ...
Leer Registros SX1262:
Editar src/main.c y Uncomment ...
#define READ_REGISTERS(Vea el registro de registro de lectura a continuación)
Enviar mensaje Lora:
Editar src/main.c y Uncomment ...
#define SEND_MESSAGE(Consulte el registro de mensajes de envío a continuación)
Reciba el mensaje Lora:
Editar src/main.c y Uncomment ...
#define RECEIVE_MESSAGE(Consulte el registro de mensajes de recepción a continuación)
Tenga en cuenta que la programación GPIO CH341 está incompleta. Necesitamos que...
Init The GPIO Pins: SX126xIoInit
Src/SX126X-Linux.C#L65-L77
Registre el controlador de interrupción GPIO para DIO1: SX126xIoIrqInit
Src/SX126X-Linux.C#L79-L91
Restablecer SX1262 a través de GPIO: SX126xReset
(Por ahora reiniciamos SX1262 desconectando manualmente Pinedio USB)
Src/SX126X-Linux.C#L149-L169
Verifique SX1262 Estado ocupado a través de GPIO: SX126xWaitOnBusy
(Por ahora dormimos 10 milisegundos)
Src/SX126X-Linux.C#L171-L182
Get Dio1 PIN State: SX126xGetDio1PinState
Src/SX126X-Linux.C#L337-L344
También necesitamos hilos de fondo para recibir mensajes Lora en segundo plano ...
SRC/Main.C#L355-L408
Más sobre Pinedio USB y CH341 GPIO:
https://wiki.pine64.org/wiki/jf%27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack
Registro de salida de Pinedio USB Demo ...
Lea los registros SX1262 en Pinedio USB:
read_registers
SX126xIoInit
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: a2 22
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 00 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x00 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 01 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x01 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 02 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x02 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 03 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x03 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 04 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x04 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 05 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x05 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 06 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x06 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 07 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x07 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 08 00 00
spi rx: a2 a2 a2 a2 80
TODO: SX126xWaitOnBusy
Register 0x08 = 0x80
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 09 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x09 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0a 00 00
spi rx: a2 a2 a2 a2 01
TODO: SX126xWaitOnBusy
Register 0x0a = 0x01
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0b 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0b = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0c 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0c = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0d 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0d = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0e 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0e = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0f 00 00
spi rx: a2 a2 a2 a2 00
TODO: SX126xWaitOnBusy
Register 0x0f = 0x00
Done!
Vea a continuación el registro de registros de lectura DMESG.
Transmita el mensaje Lora 29 byte en Pinedio USB:
Precaución: Enviar un mensaje Lora en Pinedio USB (no BL602) por encima de 29 bytes causará corrupción de mensajes.
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: ac 2c
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: ac ac
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 02 01 02 01 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSend: PreambleLength=8, HeaderType=0, PayloadLength=29, CrcMode=1, InvertIQ=0
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 1d 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=2, data_length=29
spi tx: 0e 00 50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 83 00 00 00
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
Done!
Tenga en cuenta que el mensaje Lora de 29 bytes transmitido por Pinedio USB es ...
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18
Consulte a continuación el registro de mensajes de envío DMESG.
Cuando ejecutamos este transmisor de Lora en Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
El mensaje de 28 bytes transmitido por WisBlock es recibido OK por Pinedio USB.
PRECAUCIÓN: ¡Recibir un mensaje Lora en Pinedio USB (no BL602) por encima de 28 bytes causará corrupción de mensajes!
Aquí está el registro de mensajes de recepción de Pinedio USB ...
(Consulte a continuación el registro del transmisor WISBLOCK)
gcc -o lora-sx1262
npl/linux/src/os_eventq.cc
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble
-pthread -lrt -lstdc++
cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: d4 54
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00
spi rx: a2 a2 a2 a2 04
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00
spi rx: a2 a2 a2 a2 fe
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07
spi rx: a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00
spi rx: a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00
spi rx: a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00
spi rx: a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00
spi rx: a2 a2 a2 a2 0d
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1e 2f 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d4 d4 d4 d4
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 16
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00
spi rx: d2 d2 1c 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00
spi rx: d2 d2 1c 30 1e
status=0xd2
TODO: SX126xWaitOnBusy
Rx done:
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04
spi rx: d2 d2
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00
spi rx: 80 80
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: a2 a2 a2 a2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff
spi rx: d2 d2 d2 d2
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00
spi rx: d2 d2 00 00
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00
spi rx: d2 d2 d2
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
Done!
Tenga en cuenta que el mensaje Lora de 28 bytes recibido por Pinedio USB es ...
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
Consulte a continuación el registro de mensajes de recepción DMESG.
Cuando ejecutamos este receptor de Lora en Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-reger
El mensaje de 29 bytes transmitido por Pinedio USB es recibido OK por Wisblock ...
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRaP2P Rx Test
=====================================
Starting Radio.Rx
OnRxDone: Timestamp=18, RssiValue=-28 dBm, SnrValue=13, Data=50 49 4E 47 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18
Precaución: Enviar un mensaje Lora en Pinedio USB (no BL602) por encima de 29 bytes causará corrupción de mensajes.
Cuando ejecutamos el firmware sdk_app_lora en Pinedio Stack BL604, Wisblock recibe el mensaje de 64 bytes OK.
Pero los mensajes de 64 bytes enviados por Pinedio USB están constantemente confusos cuando Wisblock recibe.
(CH341 SPI parece tener problemas para transferir un bloque de 32 bytes)
Cuando ejecutamos este transmisor de Lora en Rakwireless Wisblock ...
https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio
El mensaje de 28 bytes transmitido por WisBlock es recibido OK por Pinedio USB.
Aquí está el registro del transmisor Wisblock ...
> Executing task: platformio device monitor <
--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201 9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRap2p Tx Test
=====================================
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16
OnTxDone
PRECAUCIÓN: ¡Recibir un mensaje Lora en Pinedio USB (no BL602) por encima de 28 bytes causará corrupción de mensajes!
(CH341 SPI parece tener problemas para transferir un bloque de 32 bytes)
Registro de DMESG Al conectar Pinedio USB a Pinebook Pro ...
usb 3-1:
new full-speed USB device number 2 using xhci-hcd
New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
New USB device strings: Mfr=0, Product=2, SerialNumber=0
Product: USB UART-LPT
spi-ch341-usb 3-1:1.0:
ch341_usb_probe:
connect device
bNumEndpoints=3
endpoint=0 type=2 dir=1 addr=2
endpoint=1 type=2 dir=0 addr=2
endpoint=2 type=3 dir=1 addr=1
ch341_cfg_probe:
output cs0 SPI slave with cs=0
output cs0 gpio=0 irq=0
output cs1 SPI slave with cs=1
output cs1 gpio=1 irq=1
output cs2 SPI slave with cs=2
output cs2 gpio=2 irq=2
input gpio4 gpio=3 irq=3
input gpio6 gpio=4 irq=4
input err gpio=5 irq=5
input pemp gpio=6 irq=6
input int gpio=7 irq=7 (hwirq)
input slct gpio=8 irq=8
input wait gpio=9 irq=9
input autofd gpio=10 irq=10
input addr gpio=11 irq=11
output ini gpio=12 irq=12
output write gpio=13 irq=13
output scl gpio=14 irq=14
output sda gpio=15 irq=15
ch341_spi_probe:
start
SPI master connected to SPI bus 1
SPI device /dev/spidev1.0 created
SPI device /dev/spidev1.1 created
SPI device /dev/spidev1.2 created
done
ch341_irq_probe:
start
irq_base=94
done
ch341_gpio_probe:
start
ch341_gpio_get_direction:
gpio=cs0 dir=0
gpio=cs1 dir=0
gpio=cs2 dir=0
gpio=gpio4 dir=1
gpio=gpio6 dir=1
gpio=err dir=1
gpio=pemp dir=1
gpio=int dir=1
gpio=slct dir=1
gpio=wait dir=1
gpio=autofd dir=1
gpio=addr dir=1
gpio=ini dir=0
gpio=write dir=0
gpio=scl dir=0
gpio=sda dir=0
ch341_gpio_probe:
registered GPIOs from 496 to 511
done
connected
ch341_gpio_poll_function:
start
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
Esto significa que el nuevo controlador SPI CH341 ha sido cargado.
Si vemos esto en su lugar ...
usb 3-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 3-1: Product: USB UART-LPT
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
ch341 3-1:1.0: ch341-uart converter detected
usb 3-1: ch341-uart converter now attached to ttyUSB0
spi_ch341_usb: loading out-of-tree module taints kernel.
usbcore: registered new interface driver spi-ch341-usb
Significa que se ha cargado el controlador CH341 que no SPI anterior.
Para arreglar esto ...
Desenchufar Pinedio USB
Ingresar...
sudo rmmod ch341Enchufe Pinedio USB
Ingresar...
dmesgY vuelva a verificar los mensajes.
Registro de DMESG cuando Pinedio USB está leyendo Registros SX1262 ...
audit: type=1105 audit(1635493969.129:144): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
audit: type=1106 audit(1635493969.499:145): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
Registro DMESG cuando Pinedio USB está transmitiendo un paquete Lora de 29 bytes ...
Precaución: Enviar un mensaje Lora en Pinedio USB (no BL602) por encima de 29 bytes causará corrupción de mensajes.
audit: type=1105 audit(1634994194.295:1270): pid=72110 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
audit: type=1701 audit(1634994203.075:1271): auid=1000 uid=0 gid=0 ses=4 subj==unconfined pid=72111 comm="lora-sx1262" exe="/home/luppy/lora-sx1262/lora-sx1262" sig=6 res=1
Tenga en cuenta que si intentamos transmitir un paquete de 64 bytes, no aparecerá en el registro DMESG.
Registro de DMESG cuando Pinedio USB recibe un paquete Lora de 28 bytes ...
PRECAUCIÓN: ¡Recibir un mensaje Lora en Pinedio USB (no BL602) por encima de 28 bytes causará corrupción de mensajes!
audit: type=1105 audit(1635046697.907:371): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
audit: type=1106 audit(1635046711.037:372): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
Los pines se definen aquí en include/sx126x-board.h
De include/sx126x-board.h :
// Below are the pin numbers for PineDio Stack BL604 with onboard SX1262.
// TODO: Change the pin numbers for your SX1262 connection to BL602 / BL604
#define SX126X_SPI_IDX 0 // SPI Port 0
#define SX126X_SPI_SDI_PIN 0 // SPI Serial Data In Pin (formerly MISO)
#define SX126X_SPI_SDO_PIN 17 // SPI Serial Data Out Pin (formerly MOSI)
#define SX126X_SPI_CLK_PIN 11 // SPI Clock Pin
#define SX126X_SPI_CS_PIN 15 // SPI Chip Select Pin
#define SX126X_SPI_CS_OLD 8 // Unused SPI Chip Select Pin
#define SX126X_NRESET 18 // Reset Pin
#define SX126X_DIO1 19 // DIO1
#define SX126X_BUSY_PIN 10 // Busy Pin
#define SX126X_DEBUG_CS_PIN 5 // Debug Chip Select Pin, mirrors the High / Low State of SX1262 Chip Select Pin. Set to -1 if not needed.
#define SX126X_TCXO_WAKEUP_TIME 5 // Time required for the TCXO to wakeup (milliseconds)
#define SX126X_SPI_BAUDRATE (200 * 1000) // SPI Frequency (200 kHz) Para transmitir y recibir paquetes Lora con el controlador, ejecute el firmware de demostración sdk_app_lora BL602 ...
sdk_app_lora : BL602 Firmware de demostración para Lora SX1262 / SX1276Aquí hay un registro de muestra ...
# create_task
# init_driver
SX126xReset
SX126xIoInit
SX126X interrupt init
SX126X register handler: GPIO 11
SX126xWakeup
SX126xGetDeviceId: SX1262
SX126xSetRfTxPower
SX126xGetDeviceId: SX1262
# send_message
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# send_message
SX126xWakeup
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done:
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a
# receive_message
SX126xWakeup
RadioOnRxTimeoutIrq
Rx timeout
