الصفحة الرئيسية>المتعلقة بالبرمجة>كود الذكاء الاصطناعي
تنزيل

برنامج تشغيل Lora لـ Semtech SX1262 على Linux (محول Pinedio USB) و BL602 (Pinedio Stack BL604)

ل SX1262 على Apache Nuttx RTOs ، انظر فرع lorawan

اقرأ المقالات ...

  • "قم ببناء برنامج تشغيل Linux لمحول USB Pinedio Lora SX1262"

  • "Lorawan على لوحة Pinedio Stack BL604 RISC-V"

  • "Pinecone BL602 يتحدث لوروان"

  • "شبكة الأشياء على Pinedio Stack BL604 RISC-V Board"

تحذير: إرسال رسالة Lora على Pinedio USB (وليس BL602) فوق 29 بايت سيؤدي إلى فساد الرسائل!

تحذير: تلقي رسالة Lora على Pinedio USB (وليس BL602) فوق 28 بايت سيؤدي إلى فساد الرسائل!

(يبدو أن CH341 SPI تواجه مشكلة في نقل كتلة من 32 بايت)

لـ BL602 / BL604: لإضافة هذا السائق إلى مشروع BL602 / BL604 الحالي: 

 cd bl_iot_sdk/components/3rdparty
git submodule add https://github.com/lupyuen/lora-sx1262

تم نقله من تطبيق Semtech المرجعي لسائق SX1262 ...

https://github.com/lora-net/loramac-node/tree/master/src/radio/sx126x

بناء سائق USB Pinedio

لبناء Pinedio USB Driver على Pinebook Pro Manjaro ARM64 ... 

 # # Install DKMS
sudo pacman -Syu dkms base-devel --needed

# # Install Kernel Headers for Manjaro: https://linuxconfig.org/manjaro-linux-kernel-headers-installation
uname -r 
# # Should show "5.14.12-1-MANJARO-ARM" or similar
sudo pacman -S linux-headers
pacman -Q | grep headers
# # Should show "linux-headers 5.14.12-1" or similar

# # Reboot to be safe
sudo reboot now

# # Install CH341 SPI Driver
git clone https://github.com/rogerjames99/spi-ch341-usb.git
pushd spi-ch341-usb
# # TODO: Edit Makefile and change...
# #   KERNEL_DIR  = /usr/src/linux-headers-$(KVERSION)/
# # To...
# #   KERNEL_DIR  = /lib/modules/$(KVERSION)/build
make
sudo make install
popd

# # Unload the module ch341 if it has been automatically loaded
lsmod | grep ch341
sudo rmmod ch341

# # Load the new module
sudo modprobe spi-ch341-usb

# # Plug in PineDio USB and check that the module has been correctly loaded.
# # See dmesg Log below. This needs to be checked every time we reboot
# # our computer and when we plug in PineDio USB.
dmesg

# # If we see "spi_ch341_usb: loading out-of-tree module taints kernel",
# # Unplug PineDio USB, run "sudo rmmod ch341", plug in PineDio USB again
# # and recheck dmesg.

# # Download PineDio USB Driver
git clone --recursive https://github.com/lupyuen/lora-sx1262
cd lora-sx1262

# # TODO: Edit src/main.c and uncomment READ_REGISTERS, SEND_MESSAGE or RECEIVE_MESSAGE.
# # See "PineDio USB Operations" below

# # Build PineDio USB Driver
make

# # Run PineDio USB Driver Demo.
# # See Output Log below.
sudo ./lora-sx1262

المزيد عن Pinedio USB و CH341 SPI:

https://wiki.pine64.org/wiki/jf٪27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack

العمليات Pinedio USB

يدعم عرض Pinedio USB 3 عمليات ...

  1. اقرأ سجلات SX1262:

    تحرير src/main.c و unflemment ... 

     #define READ_REGISTERS

    (انظر سجل القراءة أدناه)

  2. أرسل رسالة لورا:

    تحرير src/main.c و unflemment ... 

     #define SEND_MESSAGE

    (انظر سجل إرسال رسالة أدناه)

  3. تلقي رسالة لورا:

    تحرير src/main.c و unflemment ... 

     #define RECEIVE_MESSAGE

    (انظر سجل رسالة استقبال أدناه)

لاحظ أن برمجة GPIO CH341 غير مكتملة. نحن بحاجة إلى ...

  1. init دبابيس GPIO: SX126xIoInit

    SRC/SX126X-Linux.c#L65-L77

  2. سجل معالج مقاطعة GPIO لـ DiO1: SX126xIoIrqInit

    SRC/SX126X-Linux.c#L79-L91

  3. إعادة تعيين SX1262 عبر GPIO: SX126xReset

    (في الوقت الحالي ، نعيد تعيين SX1262 عن طريق فصل Pinedio USB يدويًا)

    SRC/SX126X-Linux.c#L149-L169

  4. تحقق من SX1262 الحالة المزدحمة عبر GPIO: SX126xWaitOnBusy

    (الآن ننام 10 مللي ثانية)

    SRC/SX126X-Linux.c#L171-L182

  5. Get DiO1 Pin State: SX126xGetDio1PinState

    SRC/SX126X-Linux.C#L337-L344

نحتاج أيضًا إلى مؤشرات ترابط الخلفية لتلقي رسائل لورا في الخلفية ...

src/main.c#l355-l408

المزيد عن Pinedio USB و CH341 GPIO:

https://wiki.pine64.org/wiki/jf٪27s_note_on_pinedio_devices#raw_lora_communication_between_usb_lora_adapter_and_pinedio_stack

سجل إخراج USB Pinedio

سجل الإخراج من Pinedio USB Demo ...

قراءة السجلات

اقرأ سجلات SX1262 على Pinedio USB: 

 read_registers
SX126xIoInit
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: a2 22 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 00 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x00 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 01 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x01 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 02 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x02 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 03 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x03 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 04 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x04 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 05 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x05 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 06 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x06 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 07 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x07 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 08 00 00 
spi rx: a2 a2 a2 a2 80 
TODO: SX126xWaitOnBusy
Register 0x08 = 0x80
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 09 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x09 = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0a 00 00 
spi rx: a2 a2 a2 a2 01 
TODO: SX126xWaitOnBusy
Register 0x0a = 0x01
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0b 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0b = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0c 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0c = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0d 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0d = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0e 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0e = 0x00
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 00 0f 00 00 
spi rx: a2 a2 a2 a2 00 
TODO: SX126xWaitOnBusy
Register 0x0f = 0x00
Done!

انظر أدناه للاطلاع على سجل سجلات DMESG.

أرسل رسالة

نقل رسالة لورا 29 بايت على Pinedio USB:

تحذير: إرسال رسالة Lora على Pinedio USB (وليس BL602) فوق 29 بايت سيؤدي إلى فساد الرسائل! 

 gcc -o lora-sx1262 
npl/linux/src/os_eventq.cc 
 
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o 
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble  
-pthread -lrt -lstdc++  

cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: ac 2c 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: ac ac 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 3a a1 65 9a 
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00 
spi rx: a2 a2 a2 a2 04 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00 
spi rx: a2 a2 a2 a2 0d 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 02 01 02 01 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSend: PreambleLength=8, HeaderType=0, PayloadLength=29, CrcMode=1, InvertIQ=0
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 1d 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=2, data_length=29
spi tx: 0e 00 50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 83 00 00 00 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
Done!

لاحظ أن رسالة Lora 29 بايت التي يتم إرسالها بواسطة Pinedio USB هي ... 

 send_message
RadioSend: size=29
50 49 4e 47 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18

انظر أدناه للحصول على سجل الرسائل إرسال DMESG.

تلقي الرسالة

عندما ندير جهاز إرسال Lora هذا على Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio

تم استلام رسالة 28 بايت التي يتم إرسالها بواسطة Wisblock من قبل Pinedio USB.

تحذير: تلقي رسالة Lora على Pinedio USB (وليس BL602) فوق 28 بايت سيؤدي إلى فساد الرسائل!

هنا هو سجل الرسائل لاستلام USB Pinedio ...

(انظر أدناه للحصول على سجل جهاز الإرسال Wisblock) 

 gcc -o lora-sx1262 
npl/linux/src/os_eventq.cc 
 
src/main.o src/radio.o src/sx126x.o src/sx126x-linux.o npl/linux/src/os_callout.o npl/linux/src/os_sem.o npl/linux/src/os_task.o npl/linux/src/os_atomic.o npl/linux/src/os_time.o npl/linux/src/os_mutex.o 
-g -Wall -Wextra -Wno-unused-parameter -Wno-sign-compare -Wno-old-style-declaration -I include -I npl/linux/include -I npl/linux/include/nimble  
-pthread -lrt -lstdc++  

cc1plus: warning: command-line option ‘-Wno-old-style-declaration’ is valid for C/ObjC but not for C++
create_task
init_driver
TODO: SX126xReset
SX126xIoInit
TODO: SX126X interrupt init
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: d4 54 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9d 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 96 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8f 00 00 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetTxParams: power=22, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 16 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=9
spi tx: 1d 02 9f 00 00 00 00 00 00 00 00 00 00 
spi rx: a2 a2 a2 a2 02 08 ac 08 89 aa a9 61 9b 
TODO: SX126xWaitOnBusy
TimerInit
TimerInit
RadioSetChannel: freq=923000000
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 98 e1 e9 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 86 39 b0 00 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetTxConfig: modem=1, power=14, fdev=0, bandwidth=0, datarate=7, coderate=1, preambleLen=8, fixLen=0, crcOn=1, freqHopOn=0, hopPeriod=0, iqInverted=0, timeout=3000
RadioSetTxConfig: SpreadingFactor=7, Bandwidth=4, CodingRate=1, LowDatarateOptimize=0, PreambleLength=8, HeaderType=0, PayloadLength=255, CrcMode=1, InvertIQ=0
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 89 00 00 
spi rx: a2 a2 a2 a2 04 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 89 04 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetRfTxPower
SX126xSetTxParams: power=14, rampTime=7
SX126xGetDeviceId: SX1262
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 08 d8 00 00 
spi rx: a2 a2 a2 a2 fe 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 d8 fe 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
SX126xSetPaConfig: paDutyCycle=4, hpMax=7, deviceSel=0, paLut=1 
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 95 04 07 00 01 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 e7 38 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 8e 0e 07 
spi rx: a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 9f 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioStandby
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 80 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
RadioSetModem
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 8a 01 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=4
spi tx: 8b 07 04 01 00 
spi rx: a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=6
spi tx: 8c 00 08 00 ff 01 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: a0 00 
spi rx: a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=4, data_length=1
spi tx: 1d 07 36 00 00 
spi rx: a2 a2 a2 a2 0d 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 07 36 0d 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioSetRxConfig done
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1e 30 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 48 65 6c 6c 6f 00 01 02 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1e 2f 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d4 d4 d4 d4 d4 d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d4 d4 d4 d4 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 16 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 16 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
IRQ_RX_DONE
TimerStop
SX126xReadCommand: command=0x13, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 13 00 00 00 
spi rx: d2 d2 1c 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=3, data_length=28
spi tx: 1e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 
spi rx: d2 d2 d2 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
TODO: SX126xWaitOnBusy
SX126xReadCommand: command=0x14, size=3
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=3
spi tx: 14 00 00 00 00 
spi rx: d2 d2 1c 30 1e 
status=0xd2
TODO: SX126xWaitOnBusy
Rx done: 
RadioSleep
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=1
spi tx: 84 04 
spi rx: d2 d2 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID
receive_message
RadioRx
SX126xWakeup
sx126x_hal_write: command_length=1, data_length=1
spi tx: c0 00 
spi rx: 80 80 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: a2 a2 a2 a2 a2 a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: a2 a2 a2 a2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
receive_message
RadioRx
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=8
spi tx: 08 ff ff ff ff 00 00 00 00 
spi rx: d2 d2 d2 d2 d2 d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TimerStart
TimerStop
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=3, data_length=1
spi tx: 0d 08 ac 94 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=3
spi tx: 82 ff ff ff 
spi rx: d2 d2 d2 d2 
TODO: SX126xWaitOnBusy
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand: command=0x12, size=2
TODO: SX126xWaitOnBusy
sx126x_hal_read: command_length=2, data_length=2
spi tx: 12 00 00 00 
spi rx: d2 d2 00 00 
status=0xd2
TODO: SX126xWaitOnBusy
TODO: SX126xWaitOnBusy
sx126x_hal_write: command_length=1, data_length=2
spi tx: 02 00 00 
spi rx: d2 d2 d2 
TODO: SX126xWaitOnBusy
TODO: SX126xGetDio1PinState
Done!

لاحظ أن رسالة Lora 28 بايت التي تلقاها Pinedio USB هي ... 

 Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
IRQ_PREAMBLE_DETECTED
IRQ_HEADER_VALID

انظر أدناه للحصول على سجل الرسائل تلقي DMESG.

سجل المتلقي Wisblock

عندما ندير جهاز استقبال Lora هذا على Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-receiver

تم استلام رسالة 29 بايت التي يتم إرسالها بواسطة Pinedio USB على موافق من قبل Wisblock ... 

 > Executing task: platformio device monitor <

--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201  9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRaP2P Rx Test
=====================================
Starting Radio.Rx
OnRxDone: Timestamp=18, RssiValue=-28 dBm, SnrValue=13, Data=50 49 4E 47 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18

تحذير: إرسال رسالة Lora على Pinedio USB (وليس BL602) فوق 29 بايت سيؤدي إلى فساد الرسائل!

عندما نقوم بتشغيل البرنامج الثابت sdk_app_lora على Pinedio Stack BL604 ، يتلقى Wisblock رسالة 64 بايت موافق.

لكن الرسائل 64 بايت التي يتم إرسالها بواسطة Pinedio USB يتم تشويهها باستمرار عند استلامها بواسطة Wisblock.

(يبدو أن CH341 SPI تواجه مشكلة في نقل كتلة من 32 بايت)

WISBLOCK سجل المرسل

عندما ندير جهاز إرسال Lora هذا على Rakwireless Wisblock ...

https://github.com/lupyuen/wisblock-lora-transmitter/tree/pinedio

تم استلام رسالة 28 بايت التي يتم إرسالها بواسطة Wisblock من قبل Pinedio USB.

ها هو سجل جهاز إرسال Wisblock ... 

 > Executing task: platformio device monitor <

--- Available filters and text transformations: colorize, debug, default, direct, hexlify, log2file, nocontrol, printable, send_on_enter, time
--- More details at http://bit.ly/pio-monitor-filters
--- Miniterm on /dev/cu.usbmodem14201  9600,8,N,1 ---
--- Quit: Ctrl+C | Menu: Ctrl+T | Help: Ctrl+T followed by Ctrl+H ---
=====================================
LoRap2p Tx Test
=====================================
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone
send: 48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 
OnTxDone

تحذير: تلقي رسالة Lora على Pinedio USB (وليس BL602) فوق 28 بايت سيؤدي إلى فساد الرسائل!

(يبدو أن CH341 SPI تواجه مشكلة في نقل كتلة من 32 بايت)

Pinedio USB DMESG LOG

توصيل USB

سجل DMESG عند توصيل Pinedio USB إلى Pinebook Pro ... 

 usb 3-1:
new full-speed USB device number 2 using xhci-hcd
New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
New USB device strings: Mfr=0, Product=2, SerialNumber=0
Product: USB UART-LPT

spi-ch341-usb 3-1:1.0:
  ch341_usb_probe:
    connect device
    bNumEndpoints=3
      endpoint=0 type=2 dir=1 addr=2
      endpoint=1 type=2 dir=0 addr=2
      endpoint=2 type=3 dir=1 addr=1

  ch341_cfg_probe:
    output cs0 SPI slave with cs=0
    output cs0    gpio=0  irq=0 
    output cs1 SPI slave with cs=1
    output cs1    gpio=1  irq=1 
    output cs2 SPI slave with cs=2
    output cs2    gpio=2  irq=2 
    input  gpio4  gpio=3  irq=3 
    input  gpio6  gpio=4  irq=4 
    input  err    gpio=5  irq=5 
    input  pemp   gpio=6  irq=6 
    input  int    gpio=7  irq=7 (hwirq)
    input  slct   gpio=8  irq=8 
    input  wait   gpio=9  irq=9 
    input  autofd gpio=10 irq=10 
    input  addr   gpio=11 irq=11 
    output ini    gpio=12 irq=12 
    output write  gpio=13 irq=13 
    output scl    gpio=14 irq=14 
    output sda    gpio=15 irq=15 

  ch341_spi_probe:
    start
    SPI master connected to SPI bus 1
    SPI device /dev/spidev1.0 created
    SPI device /dev/spidev1.1 created
    SPI device /dev/spidev1.2 created
    done

  ch341_irq_probe:
    start
    irq_base=94
    done

  ch341_gpio_probe: 
    start

  ch341_gpio_get_direction:
    gpio=cs0    dir=0
    gpio=cs1    dir=0
    gpio=cs2    dir=0
    gpio=gpio4  dir=1
    gpio=gpio6  dir=1
    gpio=err    dir=1
    gpio=pemp   dir=1
    gpio=int    dir=1
    gpio=slct   dir=1
    gpio=wait   dir=1
    gpio=autofd dir=1
    gpio=addr   dir=1
    gpio=ini    dir=0
    gpio=write  dir=0
    gpio=scl    dir=0
    gpio=sda    dir=0

  ch341_gpio_probe:
    registered GPIOs from 496 to 511
    done
    connected

  ch341_gpio_poll_function:
    start

usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart

هذا يعني أنه تم تحميل برنامج تشغيل CH341 SPI الأحدث.

فشل توصيل USB

إذا رأينا هذا بدلاً من ذلك ... 

 usb 3-1: new full-speed USB device number 2 using xhci-hcd
usb 3-1: New USB device found, idVendor=1a86, idProduct=5512, bcdDevice= 3.04
usb 3-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
usb 3-1: Product: USB UART-LPT
usbcore: registered new interface driver ch341
usbserial: USB Serial support registered for ch341-uart
ch341 3-1:1.0: ch341-uart converter detected
usb 3-1: ch341-uart converter now attached to ttyUSB0
spi_ch341_usb: loading out-of-tree module taints kernel.
usbcore: registered new interface driver spi-ch341-usb

وهذا يعني أنه تم تحميل برنامج تشغيل CH341 الأقدم SPI.

لإصلاح هذا ...

  1. افصل Pinedio USB

  2. يدخل... 

    sudo rmmod ch341

  3. قم بتوصيل Pinedio USB

  4. يدخل... 

    dmesg

    وإعادة فحص الرسائل.

قراءة السجلات

سجل DMESG عندما يقرأ Pinedio USB سجلات SX1262 ... 

 audit: type=1105 audit(1635493969.129:144): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 1-1.1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
audit: type=1106 audit(1635493969.499:145): pid=3122 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'

أرسل رسالة

سجل DMESG عندما يقوم Pinedio USB بإرسال حزمة لورا 29 بايت ...

تحذير: إرسال رسالة Lora على Pinedio USB (وليس BL602) فوق 29 بايت سيؤدي إلى فساد الرسائل! 

 audit: type=1105 audit(1634994194.295:1270): pid=72110 uid=1000 auid=1000 ses=4 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/3 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
audit: type=1701 audit(1634994203.075:1271): auid=1000 uid=0 gid=0 ses=4 subj==unconfined pid=72111 comm="lora-sx1262" exe="/home/luppy/lora-sx1262/lora-sx1262" sig=6 res=1

لاحظ أنه إذا حاولنا نقل حزمة 64 بايت ، فلن تظهر في سجل DMESG.

تلقي الرسالة

سجل DMESG عندما يتلقى Pinedio USB حزمة لورا 28 بايت ...

تحذير: تلقي رسالة Lora على Pinedio USB (وليس BL602) فوق 28 بايت سيؤدي إلى فساد الرسائل! 

 audit: type=1105 audit(1635046697.907:371): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_open grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=13, csChange=1, result=13
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=7, csChange=1, result=7
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=31, csChange=1, result=31
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=5, csChange=1, result=5
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=2, csChange=1, result=2
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=9, csChange=1, result=9
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=4, csChange=1, result=4
spi-ch341-usb 3-1:1.0: ch341_spi_transfer_low: len=3, csChange=1, result=3
audit: type=1106 audit(1635046711.037:372): pid=29045 uid=1000 auid=1000 ses=7 subj==unconfined msg='op=PAM:session_close grantors=pam_limits,pam_unix,pam_permit acct="root" exe="/usr/bin/sudo" hostname=? addr=? terminal=/dev/pts/5 res=success'

قم بتوصيل BL602 إلى SX1262

يتم تعريف المسامير هنا في include/sx126x-board.h

من include/sx126x-board.h : 

 //  Below are the pin numbers for PineDio Stack BL604 with onboard SX1262.
//  TODO: Change the pin numbers for your SX1262 connection to BL602 / BL604
#define SX126X_SPI_IDX           0  //  SPI Port 0
#define SX126X_SPI_SDI_PIN       0  //  SPI Serial Data In Pin  (formerly MISO)
#define SX126X_SPI_SDO_PIN      17  //  SPI Serial Data Out Pin (formerly MOSI)
#define SX126X_SPI_CLK_PIN      11  //  SPI Clock Pin
#define SX126X_SPI_CS_PIN       15  //  SPI Chip Select Pin
#define SX126X_SPI_CS_OLD        8  //  Unused SPI Chip Select Pin
#define SX126X_NRESET           18  //  Reset Pin
#define SX126X_DIO1             19  //  DIO1
#define SX126X_BUSY_PIN         10  //  Busy Pin
#define SX126X_DEBUG_CS_PIN      5  //  Debug Chip Select Pin, mirrors the High / Low State of SX1262 Chip Select Pin. Set to -1 if not needed.
#define SX126X_TCXO_WAKEUP_TIME  5  //  Time required for the TCXO to wakeup (milliseconds)
#define SX126X_SPI_BAUDRATE  (200 * 1000)  //  SPI Frequency (200 kHz)

البرامج الثابتة التجريبية BL602

لنقل واستقبال حزم Lora مع برنامج التشغيل ، قم بتشغيل البرنامج الثابت sdk_app_lora BL602 ...

  • sdk_app_lora : البرامج الثابتة BL602 Demo لـ Lora SX1262 / SX1276

إليك عينة سجل ... 

 # create_task

# init_driver
SX126xReset
SX126xIoInit
SX126X interrupt init
SX126X register handler: GPIO 11
SX126xWakeup
SX126xGetDeviceId: SX1262
SX126xSetRfTxPower
SX126xGetDeviceId: SX1262

# send_message

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# send_message
SX126xWakeup

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# send_message
SX126xWakeup

RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_TX_DONE
Tx done

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup

# RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_PREAMBLE_DETECTED
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_HEADER_VALID
RadioOnDioIrq
RadioIrqProcess
SX126xReadCommand
IRQ_RX_DONE
SX126xReadCommand
SX126xReadCommand
Rx done: 
48 65 6c 6c 6f 00 01 02 03 04 05 06 07 08 09 0a 0b 0c 0d 0e 0f 10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f 20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f 30 31 32 33 34 35 36 37 38 39 3a 

# receive_message
SX126xWakeup
RadioOnRxTimeoutIrq
Rx timeout
يوسع
معلومات إضافية
تطبيقات ذات صلة
نوصي لك
أخبار ذات صلة الكل